3D打印头膜固定技术在头部肿瘤放疗的应用研究

doi:10.3760/cma.j.cn113030-20190830-00355

摘要
图/表
参考文献(18)
相关文章 (15)
点击分布统计
下载分布统计

全文: PDF (1633 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS) 背景资料

摘要目的为头部放疗患者定制个体化3D打印头膜,通过与热塑头膜对比,评价其材质的物理特性及该技术的摆位精准度。方法分别将3D打印头膜和热塑头膜置于固体水表面,通过电离室和胶片测量深度5cm处和表面剂量来进行剂量学评估。选取30例头部放疗患者随机分为对照组和试验组,分别采用热塑头膜和3D打印头膜进行固定,通过CBCT获取患者X、Y、Z方向的平移和旋转摆位误差来进行临床摆位误差评估。结果深度5cm处两种材质对射线衰减率均<1%。表面位置热塑头膜剂量升高27%,3D打印头膜升高18%。两组患者各取116组摆位误差数据,对照组和试验组X、Y、Z方向平均平移误差分别为1.29mm和1.16mm、1.42mm和1.24mm、1.38mm和1.16mm;平均旋转摆位误差分别为1.29°和1.08°、1.02°和0.96°、1.01°和1.00°。与对照组相比,试验组患者在Y、Z方向平移摆位误差和X方向旋转摆位误差不同(P<0.05),其他方向相近(P>0.05)。结论 3D打印头膜体位固定技术符合现代放疗的精准摆位要求,具有较高的临床实用价值,可用于进一步临床研究。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	王斌
	孙云川
	刘光波
	薛涛
	刘志坤
	闫慧娟
	周丽霞
	王珮烨
	赵建勇
	王鸿飞

关键词 ：三维打印, 头膜固定,个体化, 摆位误差, 头部肿瘤/放射疗法

Abstract：Objective To customize the individualized 3D printed head film for patients with head tumors undergoing radiotherapy, and to evaluate the physical properties of the material and the precision of this technology compared with the thermoplastic head film. Methods The 3D printed head film and thermoplastic head film were placed on the solid water surface, and the depth and surface dose were measured at 5 cm by ionization chamber and film, respectively. Thirty patients with head tumors receiving radiotherapy were randomly divided into the control and experimental groups. The patients were fixed with thermoplastic head film and 3D printed head film. The translational and rotational errors in the x, y and z direction were obtained by CBCT. Results The radiation attenuation rate of two materials at the depth of 5 cm was less than 1%. The dose of thermoplastic head film in the surface position was increased by 27%, and increased by 18% in the 3D printed head film. In two groups, 116 sets of setup errors were collected. The average translational setup errors in the control and experimental groups were 1.29 mm and 1.16 mm, 1.42 mm and 1.24 mm, 1.38 mm and 1.16 mm, respectively, and the average rotational setup errors were 1.29°and 1.08°, 1.02°and 0.96°, 1.01°and 1.00°, respectively. The translational setup errors in the y and z direction and rotational setup errors in the x direction significantly differed between the control and experimental groups (all P<0.05), but no statistical significance was found in the other direction (all P>0.05). Conclusion The 3D printed head film fixation meets the precise setup requirements of modern radiotherapy, which deserves further application in clinical trials.

Key words： 3D-printing Head film fixation,individuation Setup error Head tumor/radiotherapy

收稿日期: 2019-08-30

通讯作者: 孙云川,Email:flowfly@126.com

引用本文:

王斌,孙云川,刘光波等. 3D打印头膜固定技术在头部肿瘤放疗的应用研究[J]. 中华放射肿瘤学杂志, 2020, 29(11): 973-977.

Wang Bin,Sun Yunchuan,Liu Guangbo et al. Application of 3D printed head film fixation technology in radiotherapy for head tumors[J]. Chinese Journal of Radiation Oncology, 2020, 29(11): 973-977.

链接本文:

http://journal12.magtechjournal.com/Jweb_fszlx/CN/10.3760/cma.j.cn113030-20190830-00355 或 http://journal12.magtechjournal.com/Jweb_fszlx/CN/Y2020/V29/I11/973

[1] Laycock SD, Hulse M, Scrase CD, et al. Towards the production of radiotherapy treatment shells on 3D printers using data derived from DICOM CT and MRI:Preclinical feasibility studies[J]. J Radiother Pract, 2015(14):92-98. DOI:10. 1017/S1460396914000326.
[2] 张寅, 戴建荣, 李明辉, 等. 热塑面罩收缩对放疗靶区定位精度的影响[J]. 中华放射肿瘤学杂志, 2015, 24(4):454-456. DOI:10.3760/cma.j.issn.1004-4221.2015.04.025.
Zhang Y, Dai JR, Li MH, et al. The effect of the shrinkage of thermoplastic mask on patient positioning[J]. Chin J Radiat Oncol, 2015, 24(4):454-456. DOI:10.3760/cma.j.issn.1004-4221.2015.04.025.
[3] 刘裕杰, 周莉钧, 管西寅, 等. 图像引导的放射治疗在头颈部肿瘤治疗中的应用[J]. 中国癌症杂志, 2010, 20(9):707-711. DOI:10. 3969/j. issn. 1007-3639. 2010. 09. 014.
Liu YJ, Zhou LJ, Guan XY, et al. Application of image-guided radiotherapy in head-and-neck cancer[J]. China Oncol, 2010, 20(9):707-711. DOI:10.3969/j.issn.1007-3639.2010.09.014.
[4] Polat B, Wilbert J, Baier K, et al. Nonrigid patient setup errors in the head and neck region[J]. Strahlenther Onkol, 2007, 183(9):506-511. DOI:10.1007/s00066-007-1747-5.
[5] Cowley IR, Thomas SJ. The use of a laser scanning digitiser to assess the accuracy of immobilisation masks[J]. J Radiother Pract, 2006, 5(4):191-196. DOI:10.1017/S1460396906000276.
[6] 罗日顺, 戴鹏, 张鹏, 等. 三种头部固定技术在颅内肿瘤放射治疗中摆位误差的比较研究[J]. 中国医疗装备, 2018, 15(9):18-21. DOI:10.3969/J. ISSN.1672-8270.2018.09.005.
Luo RS, Dai P, Zhang P, et al. Comparative study of positioning error of three kinds of fixation techniques for head in radiotherapy of intracranial tumors[J]. China Medical Equip, 2018, 15(9):18-21. DOI:10.3969/J. ISSN.1672-8270.2018.09.005.
[7] Shih HA,Jiang SB,Aljarrah KM,et al.Internal target volume determined with expansion margins beyond composite gross tumor volume in three dimensional conformal radiotherapy for lung cancer[J]. Int J Radiat Oncol Biol Phys, 2004, 60(2):613-622. DOI:10.1016/j.ijrobp.2004.05.031.
[8] 林明, 张远, 林端, 等. 体膜塑型时间对体部肿瘤定位精度的影响[J]. 肿瘤学杂志, 2017, 23(4):349-351. DOI:10. 11735/j. issn. 1671-170X. 2017. 04. B020.
Lin M, Zhang Y, Lin D, et al. Effect of body film forming time on accuracy of tumor localization[J]. J Chin Oncol, 2017, 23(4):349-351. DOI:10.11735/j.issn.1671-170X.2017.04. B020.
[9] 张寅, 李明辉, 罗京伟. 肿瘤放疗热塑膜伸缩特性的测试[J]. 中国医疗设备, 2018, 33(7):30-32. DOI:10.3969/j.issn.1674-1633.2018.07.007.
Zhang Y, Li MH, Luo JW. Measurement of the shrinkage of thermoplastic mask in radiation therapy[J]. China Med Dev, 2018, 33(7):30-32. DOI:10.3969/j.issn.1674-1633.2018.07.007.
[10] Guckenberger M, Meyer J, Vordermark D, et al. Magnitude and clinical relevance of translational and rotational patient setup errors:A cone-beam CT study[J]. Int J Radiat Oncol Biol Phy, 2006, 65(3):934-942. DOI:10.1016/j.ijrobp.2006.02.019.
[11] Oultram S, Findlay N, Clover K, et, al. A comparison between patient self-report and radiation therapists’ ability to identify anxiety and distress in head and neck cancer patients requiring immobilization for radiation therapy[J]. J Radiother Pract, 2012, 11(1):74-82. DOI:10.1017/S1460396911000136.
[12] Goldsworthy SD, Tuke K, Latour JM. A focus group consultation round exploring patient experiences of comfort during radiotherapy for head and neck cancer[J]. J Radiother Pract, 2016, 15(2):143-149. DOI:10.1017/S1460396916000066.
[13] Sanghera B, Amis A, McGurk M. Preliminary study of potential for rapid prototype and surface scanned radiotherapy facemask production technique[J]. J Med Engin Technol, 2002, 26(1):16-21. DOI:10. 1080/03091900110102445.
[14] McKernan B, Bydder SA, Deans T, et al. Surface laser scanning to routinely produce casts for patient immobilization during radiotherapy[J]. Australasian Radiology, 2007, 51(2):150-153. DOI:10.1111/j.1440-1673.2007.01686.x.
[15] Robertson, Fiona Mary. A comparison of thermoplastic and 3D printed beam directional shells on viability for external beam radiotherapy and user experience[M]. Musselburgh:Queen Margaret University. 2017:6-7.
[16] 何岷洪, 宋坤, 莫宏斌, 等. 3D打印光敏树脂的研究进展[J]. 功能高分子学报, 2015, 28(1):102-108. DOI:10.14133/j.cnki.1008-9357.2015.01.018.
He MH, Song K, Mo HB, et al. Progress on photosensitive resins for 3D printing[J]. J Funct Polym, 2015, 28(1):102-108. DOI:10.14133/j.cnki.1008-9357.2015.01.018.
[17] Hadley SW.Kelly R,Lain K.Effects of immobilization mask material on surface dose[J].Appl Clin Med Phys, 2005, 6:l-7.DOI:10.1120/jacmp.v6i1.1957.
[18] 王俊杰. 3D打印技术与精准粒子植入治疗学[M]. 北京:北京大学医学出版社, 2016:58.
Wang JJ. 3D Printing and accurate seed implantation therapy[M]. Beijing:Peking University Medical Press, 2016:58.