AbstractObjective To investigate the design and manufacture of 3D printed compensator in electron radiation therapy for Merkel cell carcinoma, and to verify the feasibility of this technique in electron radiation therapy. Methods Computed tomography was used to collect images of a human head phantom. The delineation of target volume of Merkel cell carcinoma was simulated in the planning system and a radiotherapy plan was formulated after adding the compensator. The compensator was printed out by a 3D printer and fixed on the head phantom. A second CT scan was performed to make a new treatment plan. For the two plans, several planes parallel to the beam were selected to calculate gamma passing rates. The actual dose distribution was measured using disposable films. The gamma passing rate was compared between the film system and the planning system. The conformity index (CI) and the heterogeneity index (HI) of target volume were compared between the plans using the printed compensator and the conventional compensator of the same thickness. Comparison between the two plans was made by paired t test. Results Using the dose distribution of the plan with simulated compensator, the gamma passing rate was 94.7±2.3% in the plan with 3D printed compensator. Using the dose distribution measured by the film, the gamma passing rate was 96.6% in the plan with 3D printed compensator. Compared with the conventional compensator, the 3D printed compensator achieved a significantly elevated CI (0.85 vs. 0.69, P=0.004) and a slightly improved HI (1.30 vs. 1.26, P=0.001). Conclusions The conformal dose distribution provided by 3D printed compensator for tumors at different depths meets the clinical need.
Wang Junfeng,Li Dingyu,Huang Zhangling et al. Simulation and application of 3D printed compensator in electron radiation therapy for Merkel cell carcinoma[J]. Chinese Journal of Radiation Oncology, 2016, 25(9): 999-1002.
Wang Junfeng,Li Dingyu,Huang Zhangling et al. Simulation and application of 3D printed compensator in electron radiation therapy for Merkel cell carcinoma[J]. Chinese Journal of Radiation Oncology, 2016, 25(9): 999-1002.
[1] 张辉,王峰.皮肤Merkel 细胞癌的研究进展[J].临床肿瘤学杂志,2011,16(5):468-471.DOI:10.3969/j.issn.1009-0460.2011.05.021. Zhang H,Wang F.Advances in the study of skin Merkel cell carcinoma[J].Chin Oncol,2011,16(5):468-471.DOI:10.3969/j.issn.1009-0460.2011.05.021. [2] Foote M,Harvey J,Porceddu S,et al. The effect of radiotherapy dose and volume on relapse in merkel cell cancer of the skin[J]. Int J Radiat Oncol Biol Phys,2010,77(3):677-684.DOI:10.1016/j.ijrobp.2009.05.067. [3] Rengier F,Weber TF,Giesel FL,et al. Centerline analysis of aortic CT angiographic examinations benefits and limitations[J].Am J Roentgenol,2009,192(5):W255-W263.DOI:10.2214/AJR.08.1488. [4] Guitton TG,Brouwer K,Lindenhovius AL,et al. Diagnostic accuracy of two dimensional and three dimensional imaging and modeling of radial head fractures[J].J Hand Microsurg,2014,6(1):13-17.DOI:10.1007/s12593-013-0107-1. [5] 曾自力,宋娟荣,常晓兵,等.空气间隙对电子束吸收剂量的影响[J].中国辐射卫生,2006,15(4):465-465.DOI:10.3969/j.issn.1004-714X.2006.04.045. Zeng ZL,Song JR,Chang XB,et al. Effect of air gap on electron beam absorbed dose[J].Chin J Radiol Heal,2006,15(4):465-465.DOI:10.3969/j.issn.1004-714X.2006.04.045. [6] 汤雨龙,惠瑞宗,曹志强,等.3D打印技术在口腔种植导板制作中的应用[J].解放军医药杂志,2015,27(11):32-35.DOI:10.3969/j.issn.2095-140X.2015.11.010. Tang YL,Hui RZ,Cao ZHQ,et al.3D printing plate making plant applications in oral cavity[J].Med Pharmac J Chin People′s Liberat Army,2015,27(11):32-35.DOI:10.3969/j.issn.2095-140X.2015.11.010. [7] 郑扬,李危石,刘忠军.骨组织 3D 打印:骨再生的未来[J].北京大学学报(医学版),2015,47(2):203-206.DOI:10.3969/j.issn.1671-167X.2015.02.003. Zheng Y,Li WSH,Liu ZHJ.Bone tissue 3D printing:the future of bone regeneration[J].J Peking Univ (Heal Sci),2015,47(2):203-206.DOI:10.3969/j.issn.1671-167X.2015.02.003.
2016, Vol. 25 
